Would you like to say thanks for this free pattern?
Please consider making a donation to say thanks for making this free pattern available to you.
FREE VERSION BELOW
This flower is made in three sections which are sewn together. The round element in the center, which resembles a gumdrop, can also be used separately as a button on any other project. Instructions are included for making the flower into a brooch.
* 0.3 oz worsted-weight yarn. Samples in photo above are made with Red Heart Unforgettable, which is a self-striping yarn with long color changes.
* Sewing thread
* Jewelry findings – one (1.5”) pin back per flower (for brooch) or appropriately sized hair clip or barrette
* G/6-4.25 mm hook for Unforgettable yarn (H/8-5.0 mm hook for Super Saver)
* Yarn needle
* Regular sewing needle
4” to 5” diameter, depending on yarn and/or hook used.
bl = back loop; ch = chain; dc = double crochet (UK – treble crochet); edc = extended double-crochet (UK – extended treble crochet); hdc = half-double crochet (UK – half-treble crochet); hk = hook; lp(s) = loop(s); NJ = needle join; rnd = round; sc = single crochet (UK – double crochet); sl st = slip stitch; sstj = slip stitch to join; st(s) = stitch(es); tr = treble crochet (UK – double treble crochet); yo = yarn over.
Modified hdc – On last yarn over, do a yarn under instead of a yarn over. This will keep each stitch closer to the previous stitch, thereby eliminating unsightly gaps.
Needle join (NJ) (a.k.a. Invisible Join)
* Leaving last lp on hk, cut working yarn about 4 to 6 inches from hk. Pull newly-cut yarn out through the lp on hk, making sure to keep the last lp loose. Set hk aside and thread end of yarn through yarn needle. Insert needle from front to back under both top lps of st indicated (usually, first st of rnd). Pull tail through, keeping tension similar to surrounding sts.
* If first st of rnd is a sl st, pull tail through and keep tension same as surrounding sts. This will keep the st count accurate.
* If first st of rnd is a standing st (begun with slip knot on hk), pull tail tightly in order to keep from adding lp to st count. Insert needle under bl, from front to back of last st of rnd where yarn was originally pulled through.
* Turn work over so wrong/back side is facing and use needle to weave in end, making sure to keep tension similar to surrounding work. Snip end of yarn. Weave in ends.
Pointy picot – Ch2. Insert hk in 2nd ch from hk, yo, pull up lp and leave on hk. Insert hk under 2 front strands (front loop and loop below) of last st worked, yo, pull up lp and leave on hk. Yo, pull through all 3 lps. (The downloadable, printable version of this pattern in my Etst shop contains photos that illustrate this process.)
Rnd 1. Make magic ring, ch1. [Working over yarn tail, sc into ring, ch3] 5 times. Pull on beginning yarn tail to close ring. Sl st in first sc to join.
Rnd 2. [In next ch-3 sp: sl st, ch2, 3dc, ch2, sl st] 5 times. Sstj.
Rnd 3. Ch1. Flip piece over to work this round into the backs of the petals formed in rnd 2. Sts should not show through on front. [In next petal: sl st under 2 lower strands of middle dc, ch4] 5 times. Sstj in beginning sl st.
Rnd 4. Ch1. Flip piece over again so right side is facing you. [In next ch-4 sp: sl st, ch3, 5edc, ch3, sl st] 5 times. Sstj in beginning sl st.
Rnd 5. Ch3. Flip piece over to back again. [In next petal: sl st under 2 lower strands of middle (3rd) edc, ch5] 5 times. Sstj in first sl st. If continuing with same yarn color, skip to Rnd 6 now. Alternate method: If desired, use new color to represent leaves, attaching new yarn with [sl st under 2 lower strands in middle (3rd) edc, ch5] 5 times. Flip flower so front is facing you.
Rnd 6. Ch1 and cinch down. With front of flower facing you, [in ch-5 sp: sl st, ch4, 3tr, picot, 3tr, ch4, sl st] 5 times. NJ.
Step 1. Leaving a 12-inch beginning tail, make a slip knot, ch4, sstj in first ch made to form ring.
Step 2. Do not work over yarn tail and do not ch1. Work 18 modified hdc into ring. Cut yarn leaving a 12-inch tail. NJ to first st of rnd. Do not weave in ends. Remove yarn needle from ending yarn tail.
Step 3. Thread needle with beginning yarn tail. Whip stitch through the back-back strand of every st (loop below bl, on back of st). Be careful not to split any strands. Remove needle and gently but firmly pull yarn until center of work becomes slightly convex, with the front side out. Remove yarn needle from beginning yarn tail.
Step 4. Thread needle with ending yarn tail. Whip stitch through the front loop of every stitch around. Remove needle and pull yarn to gather the stitches, until piece takes the form of a sphere or gumdrop. Pull on both yarn tails to ensure piece is as spherical as possible. If desired, tie yarn tails in a knot. Leave both yarn tails free to use for attaching gumdrop center to flower.
Place Flower Center on top (front) of Flower, pull tails of Flower Center to back through center hole of Flower. Thread yarn needle with one tail and sew securely around posts that radiate out from center. Weave in ends. Do the same with second tail. If desired, you may use this second tail to sew flower as an applique to another project.
Yarn Circle Backing and Pin Back
Make a magic ring, ch3, 15 edc into ring. Depending on your yarn thickness, it may be necessary to add a round of 2 sc in each stitch in order to increase the diameter. Circle should fill the space inside last rnd of flower. NJ.
Using yarn and yarn needle, sew circle to back of flower to stabilize it for use as a brooch, etc. Use regular sewing needle and thread to attach pin back.
This pattern was professionally edited and fully tested.
Copyright 2018, upd 2019, by Cheryl Dee Floyd. All Rights Reserved. You are welcome to give away or to sell any items you make from this pattern. You may not copy, distribute, or otherwise publish this pattern as your own. More patterns: https://www.etsy.com/shop/CherylDeeCrochet